Specialty Audio

Secure signs, mounts and other objects to round poles and columns using this band kit. The PM-Band-90 kit offers a pair of 90” long bands and tensioning hardware. This kit is designed for pole diameters from 6”(152mm) to 25”/635mm. The unique bolt kit requires only a socket wrench to secure and tension bands by hand. No special tools or equipment necessary. The 201 stainless band material is easy to work with offers high strength, a clean appearance and good resistance to oxidation and weathering. These kits are great for both indoor and outdoor use. Custom lengths are available too.

For marine applications, please ask our customer service for an alternative grade of stainless steel banding.

Standard Features

Installs with a wrench

Stainless materials for outdoor use

Two bands & bolt kits

Attaches to round poles and columns

* Not designed for square poles

Specifications

Material: Stainless Steel 2pcs 90″ long 3/4″ strap

Finish: Silver 2pcs Band Kit

Color: Silver

The BC-W3-8-9 provides a safe and secure overhead rigging point from underneath regular structural wood and Glulam overhead beams. This rugged, all-steel three-piece design will accommodate beam depths of 9” (230 mm) or more and widths from 3 inches wide to 8 inches wide (76-200 mm).

Its hang point eye is secured to a loading channel which is oriented underneath and in the center of the wood beam and swivels in the direction of the pull to minimize the side loading when a load is not vertical and splayed out from center.

Two side plates anchor into the wood beam via lag bolts or through bolts, depending upon the application. If not certain, check with a structural engineer for the best method of attachment.

The two side plates support the load channel below, which slides through both side plates and lock in permanently via two angle tabs.

The beam clamp components are powder coated in a choice of two colors, semi-gloss black and off-white.

Key Features

Load-rated suspension point

Swiveling hang point

Powder Coat finish

Easy permanent installation


Specifications

SPECIFICATIONS PACKAGE CONTENTS

Material: Structural steel 2 pcs Side plates

Finish: Powder Coat 1 pc. Load channel with swivel eye

Color: Black 2 pcs locking angle and fasteners

Weight: 20 lb/ 9.1 Kg

WLL: 980 lb at 0 degrees WLL: 380 lb at 45 degree

Design Factor: 5:1

Standard, pre-engineered channel style beam clamps anchor to a building’s beam structure and offer a safe and predictable method for suspending objects from overhead. This channel style beam clamp is adjustable, mounts flush underneath the beam’s flange and provides a centrally located mounting hole for use with many types of connections, including all-thread, yokes and U-Brackets, truss clamps, Unistrut, etc.

Use the BC3-8 channel style beam clamp to provide a load rated overhead rigging point from structural I-Beams with flange widths ranging between 3” and 8” (76-203mm). This beam clamp model provides a fast, easy and safe way to rig direct loads from overhead and a hand wrench is all that is required to secure this clamp.

Key Features

• Single center hang points

• Provides safe load-rated hang points

• Clamps securely to beam flanges ranging from 3” – 8”
  
  Specifications

  SPECIFICATIONS PACKAGE CONTENTS

  Material: Structural C-Channel 1 pc 3”-8” Beam Clamp Channel

  Finish: Powder Coat 2 pcs Locking Angle Plate

  Color: Black 2 pcs Flat Washer, 5/8”

  Design Factor:5:1 2 pcs Nyloc Nut, 5/8-11

  WLL: 2100 lbs / 953 Kg. on metal beams and 300lb / 136kg max on wooden beams

  45 Degree WLL 1680 lb / 762.0352 Kg

  Shipping Weight: 3.2 lbs / 1.45 Kg.
  
  Optional Accessories

  See Gimballed Beam Clamp

  BC-LAM-KIT for wooden beams

This all weather, stainless steel banding strap kit is designed to attach the PoleStar® Pole Adapters to 2” to 5” diameter poles. Each kit
contains 2 band assemblies. These kits, when used per instructions will support the stated working load of the selected pole adapter.
Secure signs, mounts and other objects to round poles and columns using this band kit. The PM-Band-20s kit offers a pair of 20” long
bands and tensioning hardware. This kit is designed for pole diameters up to 5”/152mm. The unique bolt kit requires only a socket wrench to secure and tension bands by hand. No special tools or equipment necessary. The 201 stainless band material is easy to work with, offers high
strength, a clean appearance and good resistance to oxidation and weathering. These kits are great for both indoor and outdoor use. Custom lengths are available too.



Standard Features

Securely attaches items to poles and columns

Specifications

Material:201 Stainless Steel Includes pack of 2 band kits

Finish: Silver

Color: Silver

WLL: 300 lbs/136 Kg

The Steerables® Line Array Wall Mount installs and aims line arrays on either side of a stage or building. It’s heavy black powder-coated steel framework assures safe installations and installs permanently. Line Arrays suspend from their own overhead rigging points, which allows for the desired tilt angle. Pan angles, up to 45 degrees left or right are achieved by way of an upper cross arm to aim the line array into the desired angle. An outdoor version, the SAS-500-WM-G, comes in a weather rated galvanized finish.


Standard Features

• Permanently supports small & mid-size line arrays

• Easy installation – goes up in minutes

• Provides up to 45 degrees of pan angle

• Utilizes the Line Array’s grid for down tilt

• Rugged black powder coat finish
  
  
  Specifications

  Material: Structural alloy steel shapes1 pc Steerables Wall Mount FrameFinish:Black Powder Coat1 pc Cross Arm KitColor: BlackPan Angle: Up to +/- 45 degreesTilt Angle: See line array specificationsWLL: 500 lb./227 KgDesign Factor: 5:1Content: 1/carton
  
  
  

The SAS-200-24 is an efficient, load rated universal wall arm system for mounting objects, such as loudspeakers weighing up to 200 lb/91 kg to walls & other vertical structures. Loudspeaker can easily be attached and aimed from walls and other vertical structures by way of the U-bracket or Yoke with ease of installation and flexibility in adjustment.

This all structural steel alloy assembly is ready to accomodate most Yoke or U-brackets mounts. The SAS-200-24 comes with hardware and is available in a black, powder coat finish for indoor use or galvanized finish for outdoor use.


Standard Features

Accomodates loudspeaker, lighting and theatrical

Yoke mounts

Mounts to walls and other vertical structural surfaces

Significant reductions in installation and planning time

Minimal wall surface area required

Accomodates standard Yoke and U-Series assemblies



Specifications

Material: Structural Steel only 1 pc Wall arm

Finish: Powder Coat 1 pc Hardware Kit

Color: Black Hardware for mounting to the wall

structure

is not included.

Tilt mechanism is sold separately.

WLL: 200 lb. / 91 kg

Design Factor: 7:1 ratio

Net Weight: 16 lb. / 7.3 Kg

Shipping Weight: 18 lb. / 8.2 Kg

Pack Count: 1 per carton

Marine Grade Safety Anchor

When the pole or column does not offer an adequate way to attach safety cables, specify the PM-Safety-6Down and corresponding band kit. This mount provides a structural method for anchoring safety cables. It installs above the pole adapter and safety cables are then secured to the safety anchor and each loudspeaker, thus by-passing the pole adapter completely.


Standard Features

Mounts to round surfaces including poles

and columns

All stainless steel construction

Load rated components

Components use common hole patterns

Cosmetic trim components included

Job-site ready


Specifications

Stainless Steel

Natural Passivated

Adaptive Technologies RK-4C is perfect for suspending loudspeakers from overhead from channel strut. 4 clutch lock assemblies makes tilting speakers to the desired degree simple and safe.


Standard Features

Suspending loudspeakers overhead from channel strut

4 clutch lock assemblies makes tilting speakers to the desired degree simple and safe


Specifications

Material: Stainless Steel Aircraft Cable 4 pcs Cable Assy

Finish: Silver 4 pcs Clutch Locks

Color: Silver 1 pc Hardware Kit

Design Factor: 5:1

Provides a load rated overhead rigging point from structural I-Beams with flange widths ranging between 12” and 17” (304-431mm ). This beam clamp model provides a fast, easy and safe way to rig direct loads from overhead and a hand wrench is all that is required to secure this clamp.

NOTE: Recommended torque = 40-50 ft/lb


Standard Features

Single center hang points for 1/2″ to 5/8″ dia. threaded rod.

Provides safe load-rated hang points

Clamps securely to beam flanges ranging from 12″ – 17″


Specifications

SPECIFICATIONS PACKAGE CONTENTS

Material: All Steel Components 1 pc 12”-17” Beam Clamp Channel

Width: 12” to 17” 2 pcs Locking Angle Plate

WLL:980 lbs / 445 Kg. 2 pcs Flat Washer, 5/8”

Finish: Powder Coat 2 pcs Nyloc Nut, 5/8-11

Color: Black

Design Factor: 5:1

Shipping Weight:7.29 lb / 3.3 Kg

The MP-1.5NPS-TA is a tube adapter that connects standard 1-½” sched-40 NPS pipes to channel strut. This adapter allows speakers and other objects to be mounted under channel strut using standard off the shelf 1-½” sched-40 NPS pipes.

The MP-1.5NPS-TA is designed to hold overhead objects with a maximum weight of 220 lbs. Maximum length of 72” long pipe is recommended.


KEY FEATURES:
For overhead strut applications.

Adapts to standard schedule-40 1½" dia. pipe.



SPECIFICATIONS:
Materials: Structural Steel

Finish: Powder Coat

Color: Black

Design Factor: 7:1

WLL: 220 lb/ 100 Kg

Shipping Weight: 2.2 lbs / 1 Kg.


PACKAGE CONTENTS:
1 pc 1½" Tube Adapter

1 pc Sound Isolation Washer

1 pc Flange Bolt ½-13X1.5

1 pc Set Screw, ¼-20

1 pc Sound Isolation Pad

1 pc Channel Retainer Nut ½-13

Provides two offset load rated rigging points from structural I-Beams with flange widths ranging between 12” and 17” (304-431 mm). This beam clamp model provides a fast, easy and safe way to rig direct loads, bridles and hitches. A hand wrench is all that is required to secure the clamp to the beam. *IMPORTANT – Beam flanges must be parallel to the floor to achieve the stated safe working loads.


Standard Features

For Beam Flanges 12″-17″

Two load-rated suspension points

Clamps quickly / permanently to I-Beams


Specifications

SPECIFICATIONS PACKAGE CONTENTS

Material: All Steel Components 2 pcs 5/8” eye nut

Width:(BC12-17-2) 12” to 17” / 304mm to 406mm 1 pc Channel Clamp

WLL:980 lb / 445 Kg WLL (VERTICAL)

Finish: Powder Coat

Color: Black

Design Factor: 5:1

45 DEG. 578 lb / 261 Kg

Standard, pre-engineered channel style beam clamps anchor to a building’s structure and offer a safe and predictable method of rigging grids, clusters, arrays and other objects from overhead. This channel style beam clamp is adjustable and mounts flush underneath the building’s I-Beams flanges. It comes equipped with a centrally located rigging point for suspending objects from wire rope, rigging chain, spansets, etc.

Use one of two channel style beam clamps to provide a load rated overhead rigging point from structural I-Beams with flange widths ranging between 12” 17”(305mm). This beam clamp model provides a fast, easy and safe way to rig direct loads, bridles and hitches from overhead and a hand wrench is all that is required to secure this clamp. The beam flanges must be parallel to the floor to achieve the stated working loads.

Key Features

Single load-rated center hang point

Provides safe load-rated hang point to 45° off center.

Two models secure to beam flanges ranging from 12” – 17” / 305mm to 432mm

SPECIFICATIONS PACKAGE CONTENTS

Materials: All Steel Components 1 pc Beam Clamp Channel

Width: (BC12-17) 12” to 17” / 305mm to 432mm 1 pc Locking Angle Plate

Finish: Powder Coat 2 pcs Flat Washer, 5/8”

Color: Black 2 pcs Nyloc Nut, 5/8-11

WLL: 980 lb / 445 Kg WLL (VERTICAL) on metal beams and 300lb / 136kg max on wooden beams 2 pcs 1/4” spacer

Bogen DRZ120 6 Zone Music & Paging System w/ FM Tuner MP3 Mic & Line Inputs

The Bogen DRZ120 is a unique, self-contained 6-zone music and paging system for small- to medium-sized applications. It combines a digital FM tuner / MP3 player with seven (7) MIC & LINE inputs. It has a 120-watt amplifier capable of driving 4–16-ohm or 70-volt speaker systems. The DRZ120 permits connection of up to six individual paging and music zones. The DRZ120 also features Bass and Treble controls and a 5-segment LED output signal level indicator. The built-in FM tuner uses a PLL synthesizer to provide accurate frequency selection. MP3 audio can be played from files (.mp3 & .wav) accessed via the USB or SD card slots on the front panel. The MIC1 Input can be set for VOX-activated override/muting of the other audio inputs. Additionally, there is a push-button activated Chime feature that produces a short, melodic series of four ascending bell-like alert tones which are played across all outputs

Features:

Self-contained, 6-zone music and paging system with FM Tuner, MP3 Player, MIC and LINE inputs.

120-watt audio output (into 8-ohms)

For use with 4-16 ohm or 70-volt speaker systems.

Enable from 1-6 zones for music or paging

7 total audio inputs - MIC1-4, Line1-3

MIC1 input uses a front 1/4” TRS connector for a balanced Lo-Z microphone

MIC1 VOX-activated muting of all other audio inputs governed via a MUTE Control

RCA inputs for LINE1-3

Built-in digital FM Tuner, with PLL synthesizer to provide accurate frequency selection

Auto station search and manual tuning

Back-lit tuner display, LCD

FM 75Ω coaxial antenna connector

Over 800 FM station presets

Bass and Treble controls

Infrared Remote Controller for FM tuner and MP3 player control:

-Volume control

-TUNER/MP3 select button

-Preset and scan channel selection

-USB/SD media select

-MP3 play/pause/forward/ backward/repeat options

-EQ mode selection (none, Classic, Jazz, Rock, Bass & Pop)

Chime button with priority output

5-segment LED output level meter

AUX post-mix LINE output

Power-on LED indicator

Rack-mountable with integral brackets

Listed to UL Standard 60065 for U.S. and Canada

FCC Part 15 compliant

Operates from nominal 120V AC, 60 Hz

Included Accessories:

21-Button Remote Control

5 ft. Male-to-Male RCA Phono Cables

5 ft. 75-Ohm Wire FM Antenna

Two (2) 3-Terminal Pluggable Euro-Block Connectors

Four (4) Rubber Feet/Stand-offs with mounting screws

Specifications:

Amplifier

Power Rating (RMS): 120 watts into 8-ohms

Distortion: < 1% Rated output power @ 1 kHz

Signal to Noise Ratio: LINE: ≥ -74dB

Audio Frequency Response: 80 Hz - 16 kHz @ 4Ω (+/-3dB)

Zone Outputs:   120 watts @70V max. for any single zone, or

20 watts @70V max. for each zone (assuming equal loads)

AUX Speaker Output: 4-16Ω

Tone Controls:  Bass: +/-10 dB @ 100 Hz

Treble: +/-10 dB @ 10 kHz

Microphone Inputs:      ≤ 3mV/1kΩ balanced (Front 1/4” TRS, Rear XLR,

Rear Euro-Block x2)

MIC1 Precedence: VOX-activated, with adjustable MUTE Control

LINE Inputs: ≤ 300mV/10kΩ unbalanced; RCA jacks

AUX Line Output: 50Ω/(1V); RCA jacks

Tuner

Station Tuning: Digital, with PLL Synthesizer

Band Coverage: FM: 87.5 to 108 MHz

Antenna: 75Ω coaxial

Preset Memory: Over 800 FM stations

Memory Scan: Automatically presets stations

Channel Indicator: Back-lit, LCD

Power/Dimension

Power Required: 120V AC nominal @ 60 Hz

Power Consumption: 250W

Overall Dimensions: 19-1/8" W x 3-1/2" H x 13-3/4" D

Product Weight: 25.2 lbs.

Bogen DDU250 16" Dynamic Gooseneck Desktop Microphone Push Talk and Lock

The Bogen DDU250 is a high-quality, dynamic, uni-directional, gooseneck desktop microphone ideal for any podium or PA system. It features a 16" long, fully flexible gooseneck stalk that is shock-mounted to a heavy zinc die cast base, a unidirectional pickup pattern, and a 10-foot cable with external contact closure outputs for the talk switches. The gooseneck permits the user to adjust the microphone’s angle and height to suit the user’s needs. Other features include a push-to-talk switch for momentary paging and a push-to-lock switch for continuous audio.

Features:
Cardioid pickup pattern
16" long, fully flexible gooseneck stalk that is shock-mounted to a heavy zinc die cast base
Push-to-lock and push-to-talk switches
10-foot cable with external contact closure outputs for the talk switches
Excellent speech intelligibility with low ambient noise
Effective feedback control
Low sensitivity to breath and popping sound
Slim, compact design to minimize distraction to the user

Specifications:
MIC Type: Desktop
Element: Moving coil dynamic
Polar Pattern: Cardioid
Impedance: 500-ohm
Frequency Response: 100 Hz to 12 kHz
Sensitivity*: -76 dB +/- 3dB
S/N Ratio: >65 dB
Cable: 10 ft., 4-conductor, 2-shielded
Switches: Push-to-lock and push-to-talk
Dimensions: 4-1/4" W x 18-1/4" H x 6-1/4" D
Product Weight: 3-1/2 lb.
Material: Zinc die cast
Finish: Matte black

Bogen VAR1 Voice Activated Relay for 70V Paging System 2 Sets of C Form

The VAR1 is a relay device that monitors audio activity over a wide range of input voltages and operates two sets of C-Form relay contacts in response to detected activity. The VAR1 can be used to detect voltages as low as signals directly from a microphone or as high as signals from 70V speaker systems. A low-level output of the detected audio, transformer-isolated from the input, is also made available for use with other equipment. The VAR1 can also be used as a balanced, low-impedance microphone pre-amp. The VAR1 is ideally suited to provide a set of contact closures for paging ports of lower cost telephone systems that do not have a set of AUX contacts to trigger paging equipment. An adjustable release delay (up to 25 seconds) keeps the paging system from dropping out in the middle of a page.

Features:
Monitors audio activity over a wide range of input voltages
Two sets of C-Form (both N.O. and N. C.) relay contacts respond to audio activity
Four levels of signals: microphone, 600-ohm line, 25V, and 70V speaker systems
Built-in balanced, low noise, high gain microphone pre-amp
Transformer-isolated, 600-ohm small signal level output of detected audio available
Works with self-amplified or central-amplified paging systems
Separate microphone pre-amp gain control
Adjustable release delay: 0.25s to 25s
Trigger threshold adjustment
Relay active indicator light
Accessories: PRS40C 12V DC Power Supply (sold separately)

Specifications:
LINE INPUT
Impedance: 600 ohms
Frequency Response: 100 Hz to 10 kHz
70V Input Impedance: 200k ohms
Output Level: 400 mVrms
25V Input Impedance: 75k ohms
Output Level: 420 mVrms
MIC PRE-AMP
Gain: 62 dB
Sensitivity: 750 microvolts, rms for 1Vrms out
Distortion: < 2%
Frequency Response: 200 Hz to 10 kHz
Output Signal-to-Noise Ratio: 55 dB
GENERAL
VOX Sensitivity: 20 mV to 150 mVrms @ 600 ohms Line input
Time Delay Range (approx.): 0.25 to 25 sec.
Relay Contact Rating: 2A/30V DC, 0.5A/120V AC
Power Requirements: External 12V to 24V DC @ 100mA (sold separately)
Dimensions: 5-3/8" W × 3-7/8" H × 1-3/8" D
Product Weight: 1 lb.

Adjustable Loudspeaker Mounting Kits support most of the mountable loudspeakers in the 85 lbs./38 kg. range, or less and its open side arm slots allow a single installer to easily mount loudspeakers in this weight range. Loudspeakers can be rotated within the arms to acquire the desired tilt angle. Separate side holes permit the angle of the speaker to be locked permanently using lag bolts. Since there are only two sizes, inventory requirements are minimal.

Fully captive arm holes permit safe, secure mounting of loudspeakers under balconies, overhangs and from ceilings. The brackets’ base gives installers multiple options for placing speakers over irregular and unpredictable mounting surfaces because of its unique mounting slot pattern.

Features:

• Packed in pairs

• Two models support most loudspeakers, weighs 85 lbs/36 kg. or less

• Compatible with EAW – MK2300i Series

• 16” and 24” hole centers match wall studs.

• Open arm slots for one man installation.

• Sound isolation gaskets block sound

• transmission through walls.

• Permanent angle set capable.

Specifications:
Material: Structural Steel Alloy
Down Tilt: Up to 60 degrees
Finish: Powder Coat
Color: Black
WLL: 85 lbs/38.6 Kg
Design Factor: 7:1 ratio
Includes an assortment of 1/4”, 5/16” and 3/8” bolts and hardware plus two 1/4” thick sound isolation gaskets.

The UniFrame is a complete mounting solution for outdoor loudspeakers. Its design combines the attributes of the PoleStar® stainless “a-lacarte” version into just two models produced in steel and then galvanized to an outdoor weather rating.

This single speaker pole mount reduces the amount of parts required for the job site and saves installation time by combining the support arm and the pole adapter together into one assembly. In addition, two stainless steel band kits are included, which only require a socket set to assemble.

The support arm is welded together for extra strength and durability. Each arm includes three attach point mounting holes at the end of the arm that allow the installer to select the desired distance between the loudspeaker and the pole.

Features:

• Uni-Frame assembly adds strength and reduces installation time.

• Longer pole interface increases structural capacity.

• Rugged outdoor galvanized finish to ASTM A123 an

• ISO1461 specifications.

• Three arm mounting points to accommodate all speaker models.

• Angled brace increases structural stability during severe

• weather conditions.

• Support arm may be oriented up or down for installation flexibility.

• Dual adapter may be secured to the Uni-Frame for a three-way installation.

Specifications:
Material: Steel Alloy
Finish: Galvanized
Color: Silver
WLL: 190 lb / 86.4 Kg single speaker
Design Factor: 10:1 ratio
*WLL = Working Load Limit

When the pole or column does not offer an adequate way to attach safety cables, specify the PM-Safety-6Down and corresponding band kit. This mount provides a structural method for anchoring safety cables. It installs above the pole adapter and safety cables are then secured to the safety anchor and each loudspeaker, thus by-passing the pole adapter completely.

Features:

• Mounts to round surfaces including poles and columns

• Galvanized

• Load rated components

• Components use common hole patterns

• Cosmetic trim components included

• Job-site ready

Specifications:
Galvanized Steel Alloy
Galvanized Passivated
WLL: 300lb / 136.078

For 6”/154mm diameter and larger poles and columns, use the PM-Mount-6UP. This all-stainless adapter offers a natural finish and supports up to 300 lb./68 Kg, in a vertical load with a 5:1 design factor. It accommodates the PM Series Support Arm, Dual Adapter and includes hardware for their attachment. There are four standard permanent band kits available in different lengths and are sold separately. Custom lengths are also available

Features:

• Mounts to round surfaces including poles and columns

• All stainless steel construction

• Load rated components

• Components use common hole patterns

• Cosmetic trim components included

• Job-site ready

Specifications:
Stainless Steel
Natural Passivated

Use the BC3-8 channel style beam clamp to provide a load rated overhead rigging point from structural I-Beams with flange widths ranging between 3” and 8” (76-203 mm). This beam clamp model provides a fast, easy and safe way to rig direct loads from overhead and a hand wrench is all that is required to secure this clamp.

Features:

• Single center hang points for 1/2″ to 5/8″ dia. threaded rod.

• Provides safe load-rated hang points

• Clamps securely to beam flanges ranging from 3″ – 8″

Specifications:
Material: All Steel Components
Width:(BC20-26-2) 20” to 26”
WLL:2100 lbs / 953 Kg.
Finish: Powder Coat
Color: Black
Design Factor: 5:1
Shipping Weight: 3.2 lbs / 1.45 Kg.
1 pc 3”-8” Beam Clamp Channel
2 pcs Locking Angle Plate.
2 pcs Flat Washer, 5/8”
2 pcs Nyloc Nut, 5/8-11

The MultiMount MM-024 Indoor Speaker Wall Mount supports loudspeakers weighing up to 60 lbs. in a vertical orientation, quickly attaching them to walls and other vertical structures. Speakers are independently aimed and locked in almost any direction or angle through the use of independent pan, tilt, and swivel adjustments.

The MultiMount MM-024 Indoor Speaker Wall Mount s unique telescoping arm acts as a convenient carrying handle to lift speakers into place then inserts into the wall mounting plate. Once inserted, the mounting plate supports the weight of the speaker leaving the installers hands free to complete the wiring and positioning process.

Tilt adjustments are made at the side of the speaker adapter plate. Panning adjustments are made at the mounting plate and a third rotation is available between the speaker and the support arm.

Features:

• Weather resistant for covered outdoor and indoor use

• Independent, no drift, pan and tilt controls

• Infinite locking adjustments

• No lock memory – no drift

• Single man speaker installations

• Optional safety cables available

• Conforms to multiple mounting hole patterns

• Including 2 x 4-1/4 and 2-3/4 x 5

Material: Structural Steel Alloy
Finish:Powder Coat
Color: Black
Tilt Rotation: 180° max.
Swivel Rotation: 140° max.
WLL: 60 lbs. (27.2 Kg) max.
Design Factor: 10:1 ratio
Net WGT: 4 lbs. (1.8 Kg) each
Shipping WGT: 5 lbs. (2.3 Kg) each
1 pc Hardware Kit
1 pc Support Arm Assy
1 pc Speaker Adapter
1 pc Mounting Plate

The MM-3RDX-18 is an adjustable ceiling speaker mount that provides pan, tilt & roll adjustments. It supports and aims speakers that are equipped with either the 2 X4-1/4 or the 2-3/4” X 5” 4-point mounting pattern.

This model aims speakers from overhead by way of a variety of tube extensions and ceiling attachments. Ceiling speakers achieve up to 360 degrees of horizontal pan angle, up to 180 degrees of tilt angle and 180 degrees of roll adjustment.

Tilt adjustments are made at the side of the speaker adapter plate, Pan-adjustments are made at the tube extension coupler and the roll feature is adjusted between the mount and the tube extension. The MM-3RDX-18 tube coupler provides a pathway for signal wire and a safety cable to pass through the tube extension to the terminal block. This makes for a clean, safe and predictable method for installing and aiming ceiling speakers.

Features:

• Weather resistant for covered outdoor and indoor use

• Indicators let installers set angles accurately

• Independent pan, tilt & roll aiming gets

• perfect sound coverage

• Adapts to standard schedule-40 ½” pipe

• Independent No drift, No memory Locking

• Works for speakers with 2 X 4-1/4 and

• 2-3/4X 5 Hole Patterns

Specifications:
Material: Structural Steel Alloy
Finish: Powder Coat
Tilt Rotation: +/-90 degrees max
Pan Rotation: 360 degrees
Color: Black
WLL: 60 lbs. (27.2 Kg) max.
Design Factor: 7:1 ratio
Net WGT: 5 lbs. (2.3 Kg.) each
Shipping WGT: 6 lbs. (2.7 Kg.) each
Pack Count: 1 unit/carton
1 pc 3-axis mount

**Sold in pairs only so you must order in quantities of 2 only **

Adjustable Loudspeaker Mounting Kits support most of the mountable loudspeakers in the 60 lbs./22 kg. range, or less and its open side arm slots allow a single installer to easily mount loudspeakers in this weight range. Loudspeakers can be rotated within the arms to acquire the desired tilt angle. Separate side holes permit the angle of the speaker to be locked permanently using lag bolts. Since there are only two sizes, inventory requirements are minimal.

Fully captive arm holes permit safe, secure mounting of loudspeakers under balconies, overhangs and from ceilings. The brackets’ base gives installers multiple options for placing speakers over irregular and unpredictable mounting surfaces because of its unique mounting slot pattern.

Features:

• Two models support most loudspeakers, weighs 60 lbs/27 kg. or less

• 16” and 24” hole centers match wall studs

• Open arm slots for one man installation

• Sound isolation gaskets block sound transmission through walls

• Permanent angle set capable.

Specifications:
Material: Structural Steel Alloy
Down Tilt: Up to 60 degrees
Finish: Powder Coat
Color: Black
WLL: 60 lbs/27 Kg
Design Factor: 7:1 ratio
Includes an assortment of 1/4”, 5/16” and 3/8” bolts and hardware plus two 1/4” thick sound isolation gaskets.

The Dual Adapter is an innovative way to mount and aim two loudspeakers and other objects (of equal weight and mass) from the same Pole or column. A variety of available mounting holes permit speakers to be installed closer or further from the pole to provide clearance for different down tilt angles. The Dual Adapter is produced from stainless steel in a natural finish and supports up to the stated maximum working load of the pole adapter . Decorative end caps provide a finished look and hardware is included to secure it to the pole adapter and/or support arm. Yokes and U-Brackets are not included.

Features:

• Mounts to round surfaces including poles and columns

• All stainless steel construction

• Load rated components

• Components use common hole patterns

• Cosmetic trim components included

• Job-site ready

• Stainless Steel

• Natural Passivated

The Steerables® Pull back and coupler cable kit serves as a pullback and coupling device for flyable loudspeakers and can be used in a wide range of rigging applications. It provides an easy and infinitely adjustable feature for loudspeakers and other objects weighing up to 220 lbs/134 kg.

SPECIFICATIONS
• Material: Stainless Steel
• 1 pc. 8 foot stainless wire rope
• Color: Black
• 2 pc. 4 inch tie wrap
• WLL: 220 lbs./99.8 kg.
• 2 pc. 1/4 inch shackles
• Length: 8inch/99mm
• 1 pc. Clutch lock mechanism
• 1 pc. 3/8 inch eyenut

The built-in hanger on the back of our DT8000 Guitar Stool provides a safe, convenient place for guitarists to store their guitar between sets. An extra-thick padded seat cushion boosts comfort and reduces fatigue. Nonslip rubber feet on all four legs increase stability and ensure the stool stays in place while protecting the floor from scratches. For efficient storage and transportation, the stool folds down.

4 non-slip rubber feet prevent slippage and damaged floors
All in one guitar stool & stand
Extra thick padded cushion for maximum comfort
Folds for easy, compact transportation and storage
Guitar hanger on back to conveniently store guitar between sets

Product Properties
2nd Tier Weight Capacity
200 lbs.
Application
Guitar stool / stand
Back Rest to Front of Cushion
12" - 15" (adjustable)
Base Spread
14.75" (W) x 22.25" (D)
Color
Black
Height (floor to cushion)
27"
Height (total)
39"
Material
Steel
Seat Dimensions
15.75" x 12" x 2

On-Stage WS7700B Large Workstation Studio Desk Rack and Keyboard Stand

Get more done with our WS7700 Workstation. This sturdy desk has a place for computers, studio monitors, MIDI controllers, rackmount components, and recording and mixing equipment, making it easy to keep gear organized and ready to use. A slide-out keyboard tray and an elevated platform for a monitor and speakers increase work space and enhance operating comfort. In addition to a spacious desktop that supports a wide range of mixers and keyboard instruments, two 3U shallow racks provide a space for rackmount components totaling 6U. To top off this efficient and orderly setup, a mobile device slot-stand and two computer holders keep delicate electronics safe and conveniently within reach.

Features:
• Center shelf keeps tools and other small accessories within easy reach, mobile device slot holder props up phones and tablets for hands-free viewing
• Dual 3U shallow racks provide space to securely mount rack components totaling 6U
• Ergonomic setup for a computer, monitor speakers, MIDI controller, rack gear, and other studio equipment
• Heavy-duty Z-frame base provides a stable foundation for reliable gear support
• Main worksurface provides plenty of space for mixers and keyboard instruments
• Sliding tray keeps the computer keyboard or a small MIDI controller at a comfortable level and slides under the main worksurface for convenient storage
• Two computer holders keep Mac and Windows desktop towers safe and off the floor
• Vents in the computer holders promote airflow to help keep computers cool

Specifications:
• Application: Recording/Mixing Desk
• Color: Black
• Computer Holder Dimensions: 9.25" (L) x 12" (D) x 28" (H)
• Construction: MDF &amp; Steel, Wood &amp; Steel
• Dimensions: 56" (L) x 32" (D) x 38" (H)
• Keyboard Tray Dimensions: 27" x 15"
• Main Work Surface Overall Dimensions: 56" (L) x 26" (D)
• Main Work Surface Usable Dimensions: 56" (L) x 17" (D)
• Main Worksurface Dimensions: 56" (L) x 26" (D)
• Rack Depth: 9.5"
• Rack Width: 19"
• Total Rack Space: 6U (3U left + 3U right), 6U Shallow (3U left + 3U right)
• Upper Work Surface Dimensions: 53" (L) x 17" (D)
• Upper Worksurface Dimensions: 53" (L) x 17" (D)
• Weight Capacity: 175 lb

On-Stage WS7500W Workstation Studio Desk with Keyboard Tray White

Our WS7500W Workstation provides a sturdy, professional-looking foundation for a home studio's computer, MIDI controller, and mixing gear. With an elevated monitor platform, a spacious desktop, and a slide-out keyboard tray, its ergonomic configuration maximizes work space and operating comfort.

The On-Stage WS7500W Workstation Studio Desk combines modern aesthetics with practical functionality, making it an essential centerpiece for any creative workspace. Designed to meet the demands of musicians, producers, and creators, this desk delivers style, durability, and ergonomic convenience.

Features:
• Desktop provides plenty of space for mixing gear, synths, and MIDI controllers
• Ergonomic setup for a computer, mixing monitors, and other studio equipment
• Heavy-duty Z-frame base provides a stable foundation for reliable gear support
• Tray keeps the keyboard within reach and slides under the desktop when not in use

Specifications:
• Application: Workstation
• Color: White and black
• Construction: Wood and Steel
• Desktop Height: 29"
• Dimensions: 43" wide x 38" High x 32.5" Deep
• Keyboard Tray Dimensions: 15" x 27"
• Keyboard Tray Height: 25"
• Main Surface Dimensions: 24" x 43"
• Upper Platform Dimensions: 17" x 39"
• Upper Platform Height: 37.5"
• Weight Capacity: 175 lbs.

On-Stage LS7730 Lighting Stand with Truss Adjustable Height

An efficient, secure way to erect and dismantle portable lighting, our LS7730 Lighting Stand with Truss adjusts in height up to 10.75', providing support for tall, complex lighting configurations. The center truss mounts eight PAR cans while two T-bars each mount four PAR cans, and hardware is included for mounting all 16 fixtures. Two stands with wide bases and nonslip feet provide exceptional stability and load balance for reliable performance even on irregular surfaces. For convenient, compact storage and transportation the light bars and truss sections detach and the tripod bases fold flat.

Features:
• Center truss mounts eight PAR cans while two T-bars each mount four PAR cans
• Hardware is included for properly mounting all 16 fixtures
• Height adjusts 65"–129" to support tall, complex lighting configurations
• Height settings are reinforced with a locking pin for reliable lighting support

Specifications:
• Application: 16 Par Lighting Stand with Truss
• Base Spread: 48"
• Color: Black
• Construction: Aluminum
• Height Adj.: 65" - 129"
• Length: 120"
• Product Type: Lighting Stand
• Truss Height: 11"
• Weight Capacity: 200 lbs total

On-Stage UTC5500 All Terrain Utility Cart Adjustable Bed

Capitalizing on large treaded wheels and a heavy-duty frame, our UTC5500 All-Terrain Utility Cart lives up to its name. This burly cart hauls 550 lb of gear in a single trip over rough or uneven surfaces including grass, gravel, dirt, and debris. The versatile bed expands to make room for large loads and it contracts to negotiate tight spaces. Ergonomically positioned handles at each end facilitate comfortable pushing, pulling, and steering by one person or by multiple people. The handles also fold flat against the bed to clear the way for oversized gear. While this capable cart is rugged and agile, it is also geared toward safety. Locking casters keep the cart from rolling during loading and unloading. Plus, eyelets on the frame provide anchor points for straps to secure equipment. And, despite its brawn, the cart folds into a compact configuration to make efficient use of storage space.

Features:
• Bed size adjusts to take on large loads or fit through tight spaces
• Handles can lie flat against the bed to clear the way for oversized gear
• Large treaded wheels tackle uneven terrain and the front wheels rotate 360° for ease of steering
• Safely hauls 550 lb of heavy gear to reduce load-in and load-out times

Specifications:
• Application: Gear transportation
• Compact Size: (L) 30" x (W) 13.5, (L) 30" x (W) 13.5", 30" x 13.6" x 11.2"
• Extended Size: (L) 52" x (W) 13.5", 52" x 13.6" x 37"
• Front Wheel: 8"
• Handle Height: 37"
• Platform Bed Height: 11", 11.
• Rear Wheel: 10"
• Weight: 34.6 lb
• Weight Capacity: 550 lbs, 550 lbs.